» Small size -easy to carry
» Can operate completely standalone or by remote control with the ansur software
» Test instruments containing modules with different protection classes in one test run i.e CF and BF (defibrillator)
» Test module separation
» Differential current measurements (optional)
» 11 patient inputs (laboratory style)
» Testing against standard or user defined limits
» Automatic, stepwise and manual test modes
» Programmable power up delay time before measurements
» Integrated keypad
» Internal memory for uploading test sequences and storing typically up to 200 equipment test results
» Built-in standard A4 protocols for on site documentation
» RS-232, Centronics and Bar code interface.
 

» QA-90
 

» Operator's manual
 

» 
 

Specifications
Voltage	Range 0-400V true RMS Resolution 0.1V Accuracy DC-100 Hz 1% of full scale ±1 LSD 100 Hz-10 kHz 2% of scale ±1 LSD Number of Tests 4 or multiple
Current Consumption	Range 1: 0-1000mA true RMS (@<250VAC) Resolution: 1mA: 0.0 to 2.0 Ω ± (2 % Accuracy: ±2% of full scale ±1 LSD No of tests: 1 or multiple Range 2: 1-16A true RMS (@<250VAC) Resolution: 1mA: Accuracy: ±1% of full scale ±1 LSD No of tests: 1 or multiple
Protective Earth	The test current is 25A or 1A, delivered from a transformer with a maximum idle voltage of 6v.  The measurement can be performed on the grounds leads or between E+ and E- Range / Accuracy Range: 0 to 2000 mohm Resolution: 1mA Accuracy: ±2% of full scale or 5% of reading No. of Tests: 1,2 or multiple
Insulating Resistance	The range of the insulating resistance may be executed between the casing and the power unit, or between patient module and power unit. Test Voltage: 500VDC through a 130 kohm limiting resistor No. of tests 1,2 or multiple Range 1: 1-50 Mohm   IResolution: 1 Mohm   Accuracy: ±2% of full scale or ±1 LSD Range 2: 51-200 Mohm   Resolution: 1 Mohm   Accuracy: ±2% of full scale or ±1 LSD
Leakage Currents	All measurements can be performed with a IEC 601.1 filter (patient equivalent), or without (flat frequency response).  The filter can be exchanged with filters covering other standards.  All measurement can be performed as true RMS measurements, or AC/DC measurements. The following leakage currents are measured: No. of Tests: » Earth leakage current 4 » Enclosure leakage current 6 or multiple » Differential current 2 » Substitute equipment current 1 » Direct current 2 » Current Fig 9.1 The following leakage currents are measured for each module: » Patient leakage current 6 » Main on applied part leakage current 2 » Patient Auxiliary current 6 » Floating dual lead measurement of leakage currents Multiple » Substitute patient current 1 In one test run a maximum of 11 modules with different protection classes may be tested.
Accuracy	Range 1: 0-99.99 µA   Resolution: 0.1 µA   Accuracy: ±2% of full scale or ±1 LSD Range 2: 100-1000 µA   Resolution: 1 µA   Accuracy: ±2% of full scale or ±1 LSD Range 3: 1.0-10.0 mA   Resolution: 1 µA   Accuracy: ±1% of full scale or ±1 LSD
Frequency Response	DC - 1 MHz (3dB) with a Crest factor: >2  The test voltage for the mains on applied part measurement is 110% of the line voltage, delivered through a limiting resistor of 47 kohm.