» Portable, ergonomic, lightweight, and easy to use
» Large, easy-to-read display with adjustable contrast
» Human-factors-designed user interface
» Tilt stand design for stand-up testing in field environments
» Five applied parts jacks and easy ECG snap connection with optional expander box
» ECG waveform tests and dual-lead measurements combine the functionality of a simulator, multimeter and electrical-safety analyzer in a single test tool
» Replaceable mains fuses keep your unit in the field and out of the repair shop
» Internal memory for 100 test records
» 20 A at 120 V current capability
» USB connection for use with Ansur and Data Viewer software (for memory download to PC)
» Two-year extended warranty (no-cost, available after first-year calibration at the Fluke Biomedical Cleveland Service Center)
» Optional Ansur automation software standardizes test procedures, compares results to standards limits, generates/stores reports and provides total digital data management
» Rigorously tested for rugged field applications, with CE and CSA in addition to the Fluke-quality-design stamp of approval

 

» ESA612
 

» Operator's manual
 

» 
 

Specifications
Voltage	Range (Mains Voltage) 90 V AC RMS to 132 VAC RMS   180 V AC RMS to 264 VAC RMS Range (Accessible Voltage) 0 to 300 VAC RMS Accuracy ± (2 % of reading + 2 LSD) Voltage Tests Mains and Point to Point
Earth Resistance	Two-Terminal Mode Test Current / Range & Accuracy >200 mA AC : 0.0 to 2.0 Ω ± (2 % of reading + 0.015 Ω)
Equipment Current	Mode AC RMS Range / Accuracy 0 to 20 A : ± 5 % of reading ± (2 counts or .2A, whichever is greater) Duty Cycle 15 A to 20 A, 5 min. on/ 5 min. off   10 A to 15 A, 7 min. on/ 3 min. off   0 A to 10 A continuous
Leakage Current	Modes * AC + DC (True RMS)   AC only   DC only Patient load selection (Input Impedance) AAMI ES1-1993 Fig.1   IEC 60601: Fig 15 Crest factor ≤ 3 Ranges 0.0 to 199.9 μA   200 to 1999 μA   2.00 to 10.00 mA Frequency Response/ Accuracy DC to 1 kHz : ± (1 % of reading + 1μA or 1 LSD, whichever is greater)   1 kHz to 100 kHz : ± (2 % of reading + 1μA or 1 LSD, whichever is greater)   1 kHz to 5 MHz (current > 1.6mA): ± (4 % of reading + 1μA or 1 LSD, whichever is greater)   100 kHz to 1 MHz : ± (5 % of reading + 1μA or 1 LSD, whichever is greater) Leakage Tests Earth (ground wire)   Chassis (enclosure)   Patient (lead to ground)   Patient Auxiliary (lead to lead)   Mains on Applied Part (lead isolation)   Direct Equipment   Direct Applied Part   Alternative Equipment   Alternative Applied Part   Accessible   Point to Point Mains on Applied Part 100 % of Mains
Differential Leakage	Ranges 75 to 199 µA   200 to 1999 µA   2.00 to 20.00 mA Accuracy ± 10 % of reading ± (2 counts or 20 µA, whichever is greater)
Insulation Resistance	Ranges / Accuracy 0.5 MΩ to 20 MΩ : ± (2 % of reading + 2 counts)   20 MΩ to 100 MΩ : ± (7.5 % of reading + 2 counts) Source Test Voltage 500 V DC   250 V DC Insulation Resistance Tests Mains-PE, AP-PE, Mains- PE, Mains-NE (non-earthed accessible conductive part) and AP- NE (non-earthed accessible conductive part)
ECG Performance Waveforms	Accuracy ± 2 %   ± 5 % for amplitude of 2 Hz Square wave only, fixed @ 1 mV Lead II configuration Waveforms / Rates ECG Complex (BPM) : 30, 60, 120, 180, and 240 Ventricular Fibrillation   Square wave (50 % duty cycle) (Hz) 0.125 and 2 Sine wave (Hz) 10, 40, 50, 60, and 100 Triangle wave (Hz) 2 Pulse (63 ms pulse width) 30 and 60
Power Ratings	Mains Voltage Outlet 120 VAC : 230 VAC Mains Voltage Inlet Power Range 90 to 132 VAC RMS : 180 to 264 VAC RMS Maximum Current 20 A : 16 A Hz 50 or 60 : 50 or 60
Physical Case	Dimensions (cm) 17.63 x 8.38 x 28.45 Dimensions (inches)  6.94 x 3.3 x 11.2 Weight 1.6kg (10.25 lb)
Environmental Specifications	Operating Temperature 10 to 40 degrees C Storage Temperature -20 to 60 degrees C Operating Humidity 10 to 90 % non-condensing Altitude To 2,000 meters

* Modes are available in all leakage tests with the exception of MAP leakages that are available only in True RMS