Overview

The Impulse 6000D Defibrillator Analyzer and Impulse 7000DP Defibrillator/Transcutaneous Pacer
Analyzer test systems represent the next generation in rugged, portable test instrumentation for biomedical technical professionals who need to ensure the proper operation and ultimate performance of critical life-support cardiac resuscitation equipment

The Impulse 6000D and Impulse 7000DP test capabilities encompass the spectrum of defibrillator pulse shapes including Lown, Edmark, monophasic trapezoidal, DC biphasic and pulsed AC biphasic. Both models feature full-range AED test and simulation technology compatibility and outperform in overall accuracy and standards compliance.
 
These ergonomic test systems are rugged and easy to carry, and both analyzers incorporate a first-rate intuitive user interface with a backlit, easy-to-read display and an internal rechargeable high-capacity battery. The industry-standard 50-ohm testload is built inside with optional test loads available for in-depth device analysis. The Impulse 6000D and Impulse 7000DP feature unique ECG lead attachment posts for safe and secure connections. Integrated 12-lead ECG simulation capabilities with independent outputs helps get the job done when testing defibrillators, transcutaneous pacemakers and ECG device performance including rate meter accuracy and alarm verification.

Both models utilize DSP- (Digital Signal Process) based technology to process waveforms and allow for future firmware, software and waveform upgrades. A standard USB interface allows for computer control and data transfer; optional Ansur PC-based automation software increases productivity by outfitting users with an easy-to-use method to standardize
testing procedures, capture waveforms and test results, and print and document data to make the Impulse 6000D and Impulse 7000DP the industry ideal in defibrillator and transcutaneous pacemaker test systems.

Features » Monophasic, biphasic, and pulsed-biphasic energy measurement » First-class measurement accuracy » Easy-to-use menu » Internal dual-purpose (defib and pacer) non-inductive (2 µH) 50 Ω testload » Isolated outputs for better measurements and low-noise ECG simulation » Both domestic and international certifications: CE, CSA, and C-tick (Australia) » Protection of pacer input against accidental application of defibrillator output » Internal high-capacity NiMH battery » Output energy, charge time and synchronization defibrillator tests » Peak voltage and current reading » Full disclosure of monophasic and biphasic defibrillator waveform timing parameters » Playback of defibrillator output waveform » 10 isolated ECG electrodes provide 12 combinations for standardized clinical signals » Pacer current, voltage, pulse rate, pulse width and energy (Impulse 7000DP only) » Test pacemaker pulse rate up to 800 PPM (Impulse 7000DP only) » Pacemaker sensitivity tests (Impulse 7000DP only) » Pacemaker refractory period tests (Impulse 7000DP only) » 60/50 Hz noise immunity test (Impulse 7000DP only) » Two-year factory warranty » Optional Ansur PC-based software plug-in available to help standardize and document testing procedures and results » Designed, tested, and built to incomparable Fluke quality standards

Models » Impulse6000D » Impulse 700DP

Standard Accessories » Battery charger » Operating/service manual » Soft vinyl carrying case

Optional Accessories » Hard-Sided Carrying Case

Specifications General Specifications General Specifications Temperature, operating 10 °C to 40 °C (50 °F to 104 °F) Temperature, storage -20 °C to +60 °C (-4 °F to +140 °F) Humidity 10 % to 90 % non-condensing Display LCD display Communications USB device port for computer control Power Internal rechargeable NiMH battery pack for nine hours (typical) operation after full charge or the battery charger can simultaneously operate the Analyzer and charge the battery Mechanical Housing:ABS Plastic Height:13 cm (5 in) Width:32 cm (13in) Depth:24 cm (9.5 in) Weights (w/ batteries):3.02 kg (6.6 lbs 0.1 oz) Defibrillator Analyzer Specifications Compatible Defibrillator Waveshapes   Lown, Edmark, Trapezoidal, DC Bi-phasic, and AC Pulsed Bi-phasic   AC Pulsed Biphasic waveform has not been approved in the United States. Autoranged Measurement   0.1 J to 600 J Accuracy 0.1 J to 360 J ±(1 % of reading + 0.1 J) 360 J to 600 J ±(1 % of reading + 0.1 J), typical   Note: For Pulsed Bi-Phasic defibrillator, specified accuracy is ±(1.5 % of reading + 0.3 J) on both ranges. Load resistance Resistance 50 Ω Accuracy ±1 %, non-inductive (<2 ׀H) Pulse trigger level   20 V Pulse width Range 1 ms to 50 ms Accuracy ±0.1 ms Voltage Range 20 V to 5000 V Accuracy ±(1 % of reading + 2 V) Current Range 0.4 A to 100 A Accuracy ±(1 % of reading + 0.1 A) Sample rate   250 kHz (4 µs sample) Maximum Average Power   12 W, equivalent to 10 defib pulses of 360 J every 5 minutes Scope Output Autorange 2000:1, 400:1 and 80:1: dependant on the range Waveform Playback Output: BNC   Output impedance: 50 Ω   Amplitude Accuracy:±5 % Charge Time Measurement Range 0.1 s to 100 s Accuracy ±0.05 s, typical Synchronization Test (Elective Cardioversion) Delay Time Measurement Timing window: : ECG R-wave peak to the defib pulse peak   Range: -120 to +380 ms; measures timing from 120 ms prior to the R-wave peak to up to 380 ms following the R-wave peak   Resolution: 1 ms   Accuracy: ±1 ms ECG waves Normal Sinus Rhythm (NSR): 10 BPM to 180 BPM, in 1 BPM steps   Atrial fibrillation: Coarse and fine   Monomorphic Ventricular Tachycardia: 120 BPM to 240 BPM, in 5 BPM steps   Asystole: Flat line Automated Defibrillator Test ECG Waves Normal Sinus 10 BPM to 300 BPM, in 1 BPM steps Ventricular Fibrillation Coarse and fine Monomorphic Ventricular Tachycardia 120 BPM to 300 BPM, in 5 BPM steps Polymorphic Ventricular Tachycardia 5 types Asystole Flat line ECG Waves ECG General Lead configuration 12-lead simulation. RA, LL, LA, RL, V1-6 with independent signal outputs Lead-to-lead impedance 1000 Ω (nominal) Rate accuracy ± 1 % of setting ECG Amplitudes Reference lead Selectable, Lead II (default) or Lead 1 Settings 0.05 mV to 0.45 mV, in 0.05 mV steps hard return 0.5 mV to 5.0 mV, in 0.5 mV steps Accuracy (All Performance waves and Normal Sinus R waves) Lead II: ± 2 % All other leads: ± 7 % Defib paddles: ± 7 % Amplitude of ECG signals relative to amplitude setting (in percent) Lead II reference:   Performance waves and R wave detection   Lead I – 70 %   Lead II – 100 %   Lead III – 30 %   Lead V1 – 100%   Lead V2 – 100%   Lead V3 – 100 %   Lead V4 – 100 %   Lead V5 – 100 %   Lead V6 – 100 %   Normal Sinus waves   Lead I – 70 %   Lead II – 100 %   Lead III – 30 %   Lead V1 – 24%   Lead V2 – 48%   Lead V3 – 100 %   Lead V4 – 120 %   Lead V5 – 112 %   Lead V6 – 80 %   Lead I reference:   Performance waves and R wave detection   Lead I – 100 %   Lead II – 150 %   Lead III – 50 %   Lead V1 – 100%   Lead V2 – 100%   Lead V3 – 100 %   Lead V4 – 100 %   Lead V5 – 100 %   Lead V6 – 100 %   Normal Sinus waves   Lead I – 100 %   Lead II – 150 %   Lead III – 50 %   Lead V1 – 24%   Lead V2 – 48%   Lead V3 – 100 %   Lead V4 – 120 %   Lead V5 – 112 %   Lead V6 – 80 % ECG Normal sinus Rates 10 BPM to 360 BPM, in 1 BPM steps ECG High level output (BNC Jack) Amplitude Range 0.5 V/mV of reference lead setting Accuracy ± 5 % Output Impedance: 50 Ω ECG on defibrillator Input Load Lead II reference 40 % of amplitude setting Lead I reference 60 % of amplitude setting ECG Performance Waves Square wave 2 Hz and 0.125 Hz Triangular wave 2 Hz and 2.5 Hz Sine waves 0.05, 0.5, 5, 10, 40, 50, 60, 100, 150, and 200 Hz Pulse 30BPM and 60 BPM, 60 ms pulse width R-Wave detection Waveform Haver-triangle Rates 30, 60, 80, 120, 200 and 250 BPM Widths 8, 10, 12 and 20 to 200 (by 10) ms Amplitudes 0.05 mV to 0.45 mV 0.05 mV hard return   0.5 mV to 5 mV, in 0.5 mV steps Accuracy ± (1 % setting + 1 ms) Noise Immunity Wave Sine Line Frequency 50 Hz or 60 Hz ( ± 0.5 Hz) Amplitude Range: 0.0 mV to 10 mV, in 0.5 mV steps   Accuracy: ± 5 % Transvenous Pacer Pulse Simulation Widths Range: 0.1, 0.2, 0.5, 1, and 2 ms.   Accuracy: ± 5 % of setting Amplitudes Range: 0 (off) and ± 2, ± 4, ±6, ±8, ±10, ±12. ±14, ±16, ±18, ±20, ±50, ±100, ±200, ±500, ±700 mV   Accuracy: ± (10 % setting + 0.2 mV) Amplitude of Transvenous Pacer Pulse Simulation signals relative to amplitude setting (in percent) Lead II reference:   Lead I – 67 %   Lead II – 100 %   Lead III – 33 %   Lead V1 – 67%   Lead V2 – 67%   Lead V3 – 67 %   Lead V4 – 67 %   Lead V5 – 67 %   Lead V6 – 67 %   Lead I reference:   Lead I – 100 %   Lead II – 150 %   Lead III – 50 %   Lead V1 – 100%   Lead V2 – 100%   Lead V3 – 100 %   Lead V4 – 100 %   Lead V5 – 100 %   Lead V6 – 100 % Arrhythmia selections Pacer Interactive (Transcutaneous Pacer, Impulse 7000DP only) Demand: 30 BPM to 360 BPM, in 1 BPM steps Asynchronous Non-Capture Non-Function Threshold (interactive pacing simulation only): 10 mA to 250 mA in 10 mA steps Supraventricular Atrial Fibrillation Coarse Atrial Fibrillation Fine Atrial Flutter Sinus Arrhythmia Missed Beat Atrial Tachycardia Paroxysmal Atrial Tachycardia Nodal Rhythm Supraventricular Tachycardia Premature Atrial PAC Nodal PNC PVC1 Left Ventricle (LV) PVC1 Left Ventricle (LV) Early PVC1 Left Ventricle (LV) R on T PVC2 Right Ventricle (RV) PVC2 Right Ventricle (RV) Early PVC2 Right Ventricle (RV) R on T Multifocal PVCs (LV and RV) Ventricular PVCs 6/min PVCs 12/min PVCs 24/min Freq Multifocal Trigeminy Bigeminy Pair PVCs Run 5 PVCs Run 11 PVCs Monomorphic VTach: 120 to 300 (5 BPM steps) Polymorphic VTach: 5 selections Ventricular Fibrillation: Coarse and Fine Asystole Conduction 1° Block 2° Block Type I 2° Block Type II 3° Block Right Bundle Branch Block (RBBB) Left Bundle Branch Block (LBBB) Transvenous Pacemaker (ECG simulation only) Atrial 80 BPM Asynchronous 75 BPM Demand with frequent sinus beats Demand with occasional sinus beats AV Sequential Non-Capture Non-Function Selectable pacer pulse parameters for transvenous simulation (Atrial & Ventricular channels are independently selectable by the user) Atrial Pacer Pulse (Note: relates only to the TV pacer) Width: 0.1, 0.2, 0.5, 1, 2 ms Polarity: + or - Amplitude: 0 (off), 2 to 20 (by 2), 50, 100, 200, 500, 700 mV Ventricular Pacer Pulse (Note: relates only to the TV pacer) Width: 0.1, 0.2, 0.5, 1, 2 ms Polarity: + or - Amplitude: 0 (off), 2 to 20 (by 2), 50, 100, 200, 500, 700 mV (BNC Jack) Accuracy ± 5 % for 2 Hz Square Wave , 50 _ output impedance Transcutaneous Pacemaker Analyzer Specifications (Impulse 7000DP only) Test Load Selections Defibrillator Testload (Internal) Fixed load: 50 Ω ±1 %, non-inductive (<2 μH) Power rating: 10 defib pulses of 360 Joules every 5 minutes Pacemaker Testloads (Internal) Variable load: 50 to 1500 Ω in 50-Ωsteps (±1 %), non-inductive (< 2uH) Power rating: 5 W (average), 40 W (peak) @ 1000 Ω Pacemaker Measurements Manufacturer specific algorithms GE Responder (1500 & 1700) MDE 300 (Medical Data Electronics) Medtronic ERS/Physio Control LIFEPAK MRL (Medical Research Laboratory/Welch Allyn) Philips/Agilent HP Schiller Medical ZOLL Medical (plus a general purpose Default Algorithm selection) Current 4 to 250 mA, ± (1% of reading + 0.02 mA) Pulse rate 5 to 800 PPM, ± (0.5% of reading + 0.1 PPM) Pulse width 1 to 100 ms, ± (0.5% of reading + 0.01 ms) Energy 1 μJ to 2 J, ± (4% of reading + 10 μJ) Demand and Asynchronous Mode Test Input pacer pulse rates 30 to 200 PPM ECG NSR wave Rate:10 to 300 BPM in 1 BPM increments. Amplitude:1 mV Underdrive rate:10 BPM minimum Overdrive rate:300 BPM maximum Sensitivity Test Automatic interactive threshold detection Compatible pacer rates: 30 to 120 PPM. ECG R Wave Waveforms:Square, Triangle, Sine Width:1 to 19 (by 1) ms. 20 to 95 (by 5) ms. 100 to 300 (by 25) ms Amplitude:0.05 to 0.95 (by 0.05) mV. 1 to 5 (by 0.5) mV Accuracy:± 5% of setting Refractory Period Tests Paced Refractory Period 20 to 500 ms Sensed Refractory Period 15 to 500 ms Accuracy ± 1 ms Pacer pulse rate 20 to 200 PPM ECG Waveform:Triangle wave Pulse Width:40 ms Amplitude:1 mV   Back to top Back to products list